Energy Harvesting is a technology that harvests small energy that is not wasted or used everyday and converts it into usable electrical energy. It is attracting attention as a source of renewable energy. Because it can acquire electrical energy directly from nature, it is an eco-friendly energy utilization technology that can maintain energy supply safety, security and sustainability and reduce environmental pollution.¹ As electronic devices become smaller, the place where the battery is located is gradually disappearing. These problems have recently emerged as a new solution to ‘Energy Harvesting’. The enormous energy that surrounds them eventually turns into sound or heat and disappears to the air. This discarded energy can be collected well and the efficiency of electronic devices can be much higher. We have not collected the [mW] power, but there is a field that can be used, and energy harvesting will play a role in small, low power electronic devices.^2,3 With advances in nanotechnology, even the smallest amount of energy that was previously abandoned can be effectively harvested. There are many advantages but many disadvantages as well. The biggest drawback is that the output is not constant. When it is cloudy or rainy, solar cells can not be used. Energy harvesting uses various physical phenomena. Body energy harvesting uses body temperature, static electricity, kinetic energy, etc., which are generated through the movement of the body.^4,5 Solar energy harvesting using sunlight,⁶ vibrational energy harvesting for generating piezoelectric elements by applying vibration or pressure, and the like.^7-9 Energy harvesting is being actively carried out mainly in Europe and the United States, and application fields will be further expanded.^10-12 In this study, energy harvesting technology using vibration energy was used, and the vibration energy was collected by attaching a generator to the suspension system, so that it could perform the self-generation function by converting it into electrical energy. Other existing researchers are also in the process of studying the energy harvesting of the body.^13-15 Outer PM 8 pole 8 slot model was used and the power generation effect of the linear generator was compared with the change of the road surface amplitude, road surface frequency and vehicle speed. Through Carsim-simulink, we confirmed the power generation effect according to the vehicle speed. Model simulation and power generation simulation were conducted using MAXWELL, a commercial electromagnetic analysis program. The optimum design is performed because it is necessary to design the optimal design because it requires the maximum power generation amount and minimum magnetic force.

The suspension is composed of a shock absorber, a spring, a suspension arm, etc., and is positioned between the axle and the vehicle body or the frame, supports the weight of the vehicle from the road surface while driving the vehicle, and alleviates the vibration of the wheel. Suspension is a viscous hydraulic system that absorbs shocks and is constructed with springs to suppress and eliminate vibration.^16-18 In this study, the suspension system is designed to generate electric energy through energy harvesting by absorbing up - down vibration energy. As shown in Fig. 1, the energy harvesting suspension system has a structure that can generate electric energy with vibration energy while removing vibration energy from damper.

Fig. 1 
Structure of regenerative suspension

Fig. 2 shows the structure of the existing suspension system and harvesting suspension system.

Fig. 2 
Electromagnetic damper of vehicle suspension

The generator used in this paper is an outer 8 slot 8 pole generator as shown in Fig. 3 and consists of a radial magnet, an axial magnet, a core, a coil, and a shaft and a guide for linear motion. The 8 slot 8 pole structure has eight coils and eight magnets facing each other. The structure of the linear generator has an inner and outer generator structure. In this paper, the outer PM 8 slot 8 pole structure is selected to reduce the magnetic force. Simulation shows that the outer linear generator has relatively low magnetic force. Nd-Fe (Neodymium Ferrite) magnets with high magnetic force were used as magnets. The axial magnet is 40 SH and the radial magnet is 50 SH. In order to smooth the flow of magnetic force, the core is made of S20C material and arranged in order with the coil. It is an axisymmetric model and can be divided into a mover and a stator. The generation motion is established by the relative motion of the mover and the stator. The up and down motion of the mover with the permanent magnet passes over the coils of the stator, and the electromotive force (EMF) is induced in the coil to generate electric energy. Can be expressed by the following Eq. (1).

Fig. 3 
8 Slot 8 Pole 1/4 model

Where N is the number of turns of the coil, phi is the flux passing through each turn for a time t, and dz/dt is the velocity for the z direction displacement of the mover.

In this study, the power generation and magnetic force were observed according to the driving conditions of the vehicle. Sensitivity analysis was conducted to find out which conditions are most sensitive to each condition. The ratio of the rate of change of the average power generation to the rate of change of design variables is shown expressed in Eq. (4).

In Eq. (4), S represents the sensitivity, ΔX/X_initial in the denominator represents the rate of change with respect to the initial value of the design variable, and ΔW/W_initial in the numerator represents the rate of change of the corresponding generation amount. The initial condition is f = 10Hz, A = 5.625 mm, v_{vehicle velocity} = 30 km/h. The average sensitivity for road surface frequency, amplitude, and vehicle speed is shown in Fig. 12 as a graph.

Fig. 12 
Sensitivity to average power

Sensitivity to each condition was determined. The average sensitivity for each variable was 1.9451 for road surface, 1.0502 for amplitude, and 0.6258 for vehicle speed. It was confirmed that the road surface amplitude and the vehicle speed do not show a large sensitivity relative to the road surface frequency.

In this study, the verification of the power generation of the harvesting suspension system was carried out. In order to derive the optimal model with maximum power generation and minimum magnetic force, the optimal design was performed by using PIANO, a PIDO tool, with four parameters. Next, the optimal model of the linear generator was verified by using electromagnetic simulation ANSYS MAXWELL. In the initial model, the maximum power generation amount was 174.0479 W, the average power generation amount was 45.9855 W, the maximum magnetic power was 2.7002 kN, and the maximum model generation amount was 278.4210 W, the average generation amount was 70.1067 W and the maximum magnetic power was 1.7896 kN. The maximum power generation amount was 59.98%, the average power generation amount was 78.68% higher than the initial model, and the optimum power generation amount with magnetic force decreased by 66.31% was derived. Lastly, three input conditions were applied to analyze the sensitivity of power generation according to changes in road surface displacement, road surface frequency, and vehicle velocity. Suspension velocity according to vehicle velocity was derived through a simulated driving test using the Carsim-simulink. We observed that the average power generation is the most sensitive to the road surface frequency. Sensitivity to road surface frequency is 1.9451, sensitivity to road surface displacement is 1.0502, sensitivity to vehicle speed is 0.6258.